Pemadam Api Otomatis Menggunakan Flame Sensor dan MQ-2
a. Dapat merangkai rangkaian untuk pemadam api otomatis
2. Alat dan Bahan [kembali]
2. MQ-2
- Sensor MQ2
Features:
- Operating Voltage is +5V
- Can be used to Measure or detect LPG, Alcohol, Propane, Hydrogen, CO and even methane
- Analog output voltage: 0V to 5V
- Digital Output Voltage: 0V or 5V (TTL Logic)
- Preheat duration 20 seconds
- Can be used as a Digital or analog sensor
- The Sensitivity of Digital pin can be varied using the potentiometer
* Trigger Voltage (Voltage across coil) : 5V DC
* Trigger Current (Nominal current) : 70mA
* Maximum AC load current: 10A @ 250/125V AC
* Maximum DC load current: 10A @ 30/28V DC
* Compact 5-pin configuration with plastic moulding
* Operating time: 10msec Release time: 5msec
* Maximum switching: 300 operating/minute (mechanically)
- Konfigurasi Pin
* Coil End 1 : Used to trigger(On/Off) the Relay, Normally one end is connected to 5V and the other end to ground.
* Coil End 2 : Used to trigger(On/Off) the Relay, Normally one end is connected to 5V and the other end to ground.
* Common (COM) : Common is connected to one End of the Load that is to be controlled.
* Normally Close (NC) : The other end of the load is either connected to NO or NC. If connected to NC the load remains connected before trigger.
* Normally Open (NO) : The other end of the load is either connected to NO or NC. If connected to NO the load remains disconnected before trigger.
1. Collector
2. Base
3. Emitter
B. Spesifikasi :
Transistor Type : NPN
Voltage – Collector Emitter Breakdown (Max) : 45 V
Current- Collector (Ic) (Max) : 100mA
Power – Max : 625 mW
DC Current Gain (hFE) (Min) @ Ic, Vce : 110 @ 2mA, 5V
Vce Saturation (Max) @ Ib Ic : 300mV, @ 5mA, 100mA
Frequency – Transition : 300MHz
Current- Collector Cutoff (Max) : -
Mounting Type : Through Hole
Package / Case : TO-226-3, TO-92-3 (TO-226AA) Formed Leads
Packaging : Tape & Box (TB
Lead Free Status : Lead Free
RoHs Status : RoHs Compliant
1 | Positif | Diidentifikasi dengan simbol (+) atau kabel terminal yang lebih panjang. Dapat didukung oleh 6V DC |
2 | Negatif | Diidentifikasi oleh kabel terminal pendek. Biasanya terhubung ke ground sirkuit |
No: | Pin Name | Description |
1 | Terminal 1 | A normal DC motor would have only two terminals. Since these terminals are connected together only through a coil they have not polarity. Revering the connection will only reverse the direction of the motor |
2 | Terminal 2 |
B. DC Motor Specifications
- Standard 130 Type DC motor
- Operating Voltage: 4.5V to 9V
- Recommended/Rated Voltage: 6V
- Current at No load: 70mA (max)
- No-load Speed: 9000 rpm
- Loaded current: 250mA (approx)
- Rated Load: 10g*cm
- Motor Size: 27.5mm x 20mm x 15mm
- Weight: 17 grams
Pada sebuah gedung atau ruangan diperlukan sebuah alat yang dapat memadamkan api secara otomatis. Pada kesempatan kali ini pemadam api yang dibuat dengan mendeteksi api dan gas pada ruangan sehingga sensor yang digunakan yaitu flame sensor dan MQ-2.
Flame sensor merupakan sensor yang mempunyai fungsi sebagai pendeteksi nyala api dimana api memiliki panjang gelombang antara 760nm-1100nm. sensor ini menggunakan infrared sebagai tranduser dalam mensensing kondisi nyala api. Suhu normal pembacaan sensor yaitu pada 25°-85°C dengan sudut pembacaan pada 60°.
Sensor MQ-2 adalah sensor yang digunakann untuk mendeteksi konsentrasi gas yang mudah terbakar di udara serta asap dan output membaca sebagai tegangan analog. Sensor ini dapat mendeteksi konsentrasi gas yang mudah terbakar di udara serta asap dan keluarannya berupa tegangan analog. Sensor dapat mengukur konsentrasi gas mudah terbakar dari 300 sampai 10.000 sensor ppm. Dapat beroperasi pada suhu dari -20°C sampai 50°C dan mengkonsumsi arus kurang dari 150 mA pada 5V.
Pemadam Api Otomatis
Baterai berfungsi sebagai sumber tegangan. Arus mengalir dari baterai ke resistor R1, ke Vcc flame sensor, ke kolektor Q2 dan ke relay, dari R1 arus menuju ke Vcc Sensor Gas, saat sensor Gas mendeteksi asap atau berlogika 1 arus akan mengalir dari Vout ke basis Transistor npn Q1 sehingga arus pada kolektor yang diterima dari relay dapat mengalir ke emiter transistor npn lalu ke ground sehingga relay on. Saat Flame sensor mendeteksi api maka arus akan mengalir dari Vout ke basis transistor npn Q2 sehingga arus dapat mengalir dari kolektor ke emitor Q2 lalu arus mengalir ke basis Q1 sehingga transistor Q1 menyala dan relay on. saat relay on arus akan mengalir dari baterai B2 ke buzzer sehingga buzzer berbunyi dan arus juga ke motor dc sehingga motor dc berputar dalam hal ini kran terbuka. lalu dari buzze arus mengalir ke ground dari motor dc arus mengalir ke led red sehingga led menyala lalu arus mengalir ke ground. jika Sensor tidak mendeteksi asap atau api atau berlogika 0 maka relay akan off. sehingga arus mengalir dari baterai B2 ke Led Green sehingga Led menyala lalu arus mengalir ke ground
5.Video [kembali]
1. video download disini
2. Datasheet gas sensor disini
3. Rangkaian download disini
4. HTML download di sini
5. Library Sensor gas download di sini
6. Library Flame Sensor download di sini
Tidak ada komentar:
Posting Komentar